Best "Stand-On" Tonneau Cover???

[RADA]

I'm looking for something the kids (10, 14 - not my fat ass) can stand on when watching fireworks, off-road racing.

Diamondback covers are nice but expensive and BULKY...

Suggestions???

TY

 

[AnthonyRI]

I'm looking for something the kids (10, 14 - not my fat ass) can stand on when watching fireworks, off-road racing.

Diamondback covers are nice but expensive and BULKY...

Suggestions???

TY

I ended up w LOMAX ACCESS STANCE from justboltons.com I'm very happy w so far. @Johnny@JustBoltOns was super helpful in selection.
Install was reasonably easy.

I haven't jumped on top of it yet actually ..... maybe later

 

[BucsFan]

I ended up w LOMAX ACCESS STANCE from justboltons.com I'm very happy w so far. @Johnny@JustBoltOns was super helpful in selection.
Install was reasonably easy.

I haven't jumped on top of it yet actually ..... maybe later

Anthony, when it's folded, does it block your rearview camera?

 

[AnthonyRI]

Anthony, when it's folded, does it block your rearview camera?

I'm not lucky enough to have that problem yet, but yes it would. Stands up and covers the whole back window.
Which at first I was annoyed with but then I realized that any time I have something big enough to require opening the entire cover, that would have also already been blocking at least some view (tall trash barrels, etc). I do keep a spare socket to completely remove the cover (leaving the rails) which would take about 90 seconds if I really needed to - and then could lay the cover in the bed parallel to length if needed.

I spent a TON of time figuring out what the best choice of cover would be and they all had some pros and cons. So far, I'm pretty happy with this one in terms of its look, apparent durability (still very new), seemingly watertight, security, ease of use, etc.

 

[Minarets]

I ended up w LOMAX ACCESS STANCE from justboltons.com I'm very happy w so far. @Johnny@JustBoltOns was super helpful in selection.
Install was reasonably easy.

I haven't jumped on top of it yet actually ..... maybe later

That is what I have on my TRD Pro. Love it.

 

[UnloosedChewtoy]

That is also what I have on my TRX. Love it, and made in North Dakota.

 

[RADA]

I'm liking the LOMAX too...

Also looking at TonnoFlip.

Veteran Owned and Operated.

 

[yoda33073]

I'm not lucky enough to have that problem yet, but yes it would. Stands up and covers the whole back window.
Which at first I was annoyed with but then I realized that any time I have something big enough to require opening the entire cover, that would have also already been blocking at least some view (tall trash barrels, etc). I do keep a spare socket to completely remove the cover (leaving the rails) which would take about 90 seconds if I really needed to - and then could lay the cover in the bed parallel to length if needed.

I spent a TON of time figuring out what the best choice of cover would be and they all had some pros and cons. So far, I'm pretty happy with this one in terms of its look, apparent durability (still very new), seemingly watertight, security, ease of use, etc.

I like that one too, but South Florida heat doesn't like those pads on the end where you grab to roll.

 

[AnthonyRI]

So just jumped on top of mine (Lomax Access Stance) and I'd say it definitely had some give to it, but I didn't feel like I was doing damage or anything was moving. The clamps that hold the rail are in picture below, squeezing a piece of the bed rail itself, they're pretty beefy and get a good bite on it. Good enough that if I had to use it to reach something higher or strap something on top yes but I don't think I'd put two adults on it or move around a whole lot. I'd hate do inadvertently have it get out of alignment and then be leaky or bent and have the latches not line up right, etc. Definitely no jumping jacks.

This is what the clamps look like:

And the "mod" that I was "installing" at the time: